Intersil ISL8201M 20V 10A电源PWM控制方案

Intersil 公司的ISL8201M是 20V 10A输出电流的可变输出降压电源,是高性能PWM控制器,开关频率600kHz,它集成了功率MOSFET,电感和所有的无源元件,可以实现完整的DC/DC电源解决方案. ISL8201M输入电压从1V到20V, 采用单个分压电阻可实现输出电压从0.6V到5V, 峰值电流达17A,效率高达95%,可用在服务器,工业设备,POL稳压,电信和数据通信设备以及其它通用降压DC/DC转换器.本文介绍了ISL8201M的主要特性,方框图,典型应用电路和ISL8201MEVAL1Z 评估板电路图与材料清单.

The ISL8201M is a 20V, 10A output current, variable output step-down power supply. Included in the 15mmx15mm package is a high performance PWM controller switching at 600kHz, power MOSFETs, an inductor, and all the passive components required for complete DC/DC power solution.

The ISL8201M operates over an input voltage range of 1V to 20V and supports an output voltage range of 0.6V to 5V, which is set by a single dividing resistor. This high efficiency power module is capable of delivering 10A (17A peak) output with up to 95% efficiency, needing no heat sinks or airflow to meet power specifications. Only bulk input and output capacitors are needed to finish the design. Utilizing voltage-mode control, the output voltage can be precisely regulated to as low as 0.6V with up to ±1% output voltage regulation. The ISL8201M also features internal compensation, internal soft-start, auto-recovery overcurrent protection, an enable option, and pre-biased output start-up capability.

The ISL8201M is packaged in a thermally enhanced, compact (15mmx15mm) and low profile (3.5mm) over-molded QFN Package Module suitable for automated assembly by standard surface mount equipment. The ISL8201M is Pb-free and RoHS compliant.

ISL8201M主要特性:

Complete Switch Mode Power Supply

Input Voltage Range from +4.5 to +14.4V

Wide Input Voltage Range from 1V up to 20V

10A DC Output Current, 17A Peak Output Current

Adjustable +0.6V to +5V Output Range

Up to 95% Efficiency

Simple Voltage Mode Control

Fixed 600kHz Switching Frequency

Fast Transient Response

Enable Function Option

Pre-biased Output Start-up Capability

Internal Soft-Start

Overcurrent Protection by Low-Side MOSFET rDS(ON) Sensing (Non-Latching, Auto-Recovery)

Small Footprint, Low Profile Surface Mount QFN Package (15mmx15mmx3.5mm)

Pb-Free (RoHS Compliant)

ISL8201M 应用:

Servers

Industrial Equipment

Point of Load Regulation

Other General Purpose Step-Down DC/DC

Telecom and Datacom Applications



图1.ISL8201M内部方框图



图2.ISL8201M典型应用电路

ISL8201MEVAL1Z 评估板

The ISL8201MEVAL1Z POL module evaluation board is shown in Figure 3. The user can use it to evaluate the performance of the Intersil ISL8201MEVAL1Z POL Module.

This board consists of power and load connectors for source and load side, switches for PVCC bias selection and On/Off option, and other passive components.

The input voltage range is from 1V to 20V, and the output voltage range is from 0.6V to 5V. Additional PVCC bias source is not required when using an input voltage of 5V or 12V. It can connect to the input side directly. However, in wider input ranges, which are above 14V or below 5V, the PVCC bias needs to add an external source, which provides operation bias of the module. The output voltage is initially set at 1.5V for typical evaluation.



图3.ISL8201MEVAL1Z POL 评估板外形图



NOTES:

1. R1 is used to set the output voltage of ISL8201MEVAL1Z. Initial setting is 6.49kΩ for 1.5V output voltage.

2. R2 and R3, paralleling with R1, are used to adjust the output voltage of ISL8201MEVAL1Z.

3. R4 is used to set the overcurrent trip level of ISL8201MEVAL1Z. The ISL8201MEVAL1Z has integrated 3.57kΩ.

4. R18, C18 and C19 are the snubber network, which can reduce the stress for internal semiconductor.

5. R13, R14, C12, C13, C14 and C15 are the external compensation network. The ISL8201MEVAL1Z has integrated the type 3 compensation network inside the module for typical applications.

6. R15, R16, R17, R20, R21, C17, Q2 and Q3 are the power-up sequence circuit. In case of PVCC bias, power-up first, then input voltage. This circuit has to be implemented.
图4.ISL8201MEVAL1Z 评估板电路图

ISL8201MEVAL1Z 评估板材料清单(BOM):