博通BCM2070单片蓝牙解决方案

博通(Broadcom)公司的BCM2070是单片蓝牙2.1+EDR HCI解决方案.BCM2070采用65nm工艺,是单独可用的基带处理器,并集成了高性能用于蓝牙+EDR的2.4GHz收发器.完全和蓝牙2.1与以前所有的标准兼容.内置的Class 1功率放大器在1.8V电源输出功率可编程达12dBm,接收灵敏度-90 dBm. BCM2070还和WLAN和WiMAX系统共存,可广泛应用在手机和移动通信,PDA和低功耗嵌入式通信设备以及PC机和PC机主板.本文介绍了BCM2070的主要特性,方框图和主要优势,以及典型的手机和PC应用方框图.

BCM2070 Single-Chip Bluetooth® 2.1 + EDR HCI Solution
The Broadcom BCM2070 is a monolithic, single-chip, stand-alone baseband processor with a high performance integrated 2.4-GHz transceiver for Bluetooth + EDR applications. It is fully compliant with Bluetooth 2.1 and all prior standard features. Processed using advanced 65-nm LP CMOS technology, the BCM2070 offers unmatched integrated solution with the smallest footprint and lowest cost of implementing a Bluetooth system.
The use of the advanced 65-nm process enables the BCM2070 to achieve the lowest possible current consumption in all modes of operation.
The BCM2070 has an architecture that has been designed to take advantage of the EDR standard. Its superior integrated RF design enables much higher output power and lower input sensitivity, which makes the BCM2070 the ideal solution to support Bluetooth EDR. The built-in Class 1 PA, which is capable of transmitting 10 dBm output power, can be enabled with 1.8V power supply. Together with Broadcom’s leading Packet Loss Concealment (PLC) technology, which effectively reduces packet loss and bit error rates, the BCM2070 can effectively combat interference and reduce dropped connections that result from distance and physical obstructions. These translate directly into higher and more reliable throughput and greater link-range performance. The BCM2070 also includes industry collaborative coexistence solutions with WLAN and WiMAX systems. By using Broadcom’s proprietary packet redistribution scheme, the BCM2070 is the industrys first Bluetooth product that is capable of supporting up to five simultaneous A2DP
applications.
Ultra low-cost solutions can be achieved with the BCM2070 by using standard chip-on-board assembly techniques using the WLBGA package. Low-risk applications are enabled through the extensive integration of external passive and active components. All sensitive RF and analog portions of the Bluetooth radio and baseband have been
integrated into the device, including the most sensitive high-frequency matching components. This eliminates the possibility of board-level interference and degradation in performance due to the environment and board-level designs. The built-in programmable voltage regulation (1.8V to 3.6V) was added to eliminate the need for an external voltage
regulator, which further reduces the overall BOM cost. The device is capable of operation using a noisy digital 1.8 to 3.6V power supply.
BCM2070主要特性:
Processed with 65-nm LP CMOS technology
Built-in power amplifier to support class 1 transmit output power
Fully integrated balun and T/R switch eliminate all external RF matching components for class 1, 2, and 3 designs
Fully supports the Bluetooth 1.1, 1.2, 2.0, and 2.1 standards including 1-, 2-, and 3-Mbps EDR operation
Lowest current consumption in all modes of operation
ROM-based solution to eliminate external flash and/or EEPROM memory
Highest available Bluetooth radio performance of any single chip solution
90 dBm typical receiver sensitivity
Programmable output power up to +12 dBm at 1.8V supply
Minimized external BOM requirements with less than 10 external passive components
Flexible set of interfaces that include up to 4 Mbps UART, USB, H4, H5, USB, SDIO, I2C, and serial/parallel flash
Fractional-N frequency synthesizer supports any crystal or TCXO source from 12 MHz to 40 MHz
Automatic calibration and frequency detection of crystal frequency
Supports applications with WLAN and WiMAX coexistence
• Proprietary packet redistribution scheme allowing up to five headsets simultaneous A2DP music streaming
Supports wideband speech and packet-loss concealment for superior voice quality
BCM2070主要优势:
Smallest packages, lowest power consumption, and highest performance Bluetooth® 2.1 + EDR solution
Maximizes range and simplifies system integration by providing exceptional output power and receiver sensitivity
Unmatched integration tremendously simplifies board-level design for easy implementation
Achieves smallest board area requirements with minimum external BOM and smallest package size available today
Standard PCB requirement is less than 35 mm2
WLBGA COB solutions are less than 20 mm2
ROM-based solution with flexible and much improved code patching to ensure fast and easy integration
On-chip voltage regulator lowers BOM requirements and provides additional power savings capability
Minimized power dissipation over other solutions
40% savings in power compared to the previous generation of products in standard telephony headset applications
BCM2070应用:
Cellular and mobile communication devices
PDA and low-power embedded communication devices
PC and integration on PC motherboard applications
Package types available
50-pin fpBGA package (4.5 mm x 4 mm)
42-bump wafer-level BGA (WLBGA) package



图1. BCM2070方框图



图2. BCM2070典型手机应用方框图



图3. BCM2070典型PC应用方框图